Buscar en el sitio

LED Cube RED DIY Kit 8x8x8

https://www.microjpm.com/products/ad30338/
O 3mm - 2 x XH2.54 - 40Pin hembra redondo - 9 x 20P IC socket (base integrado) - 9 x 74HC573 DIP - 1 x USB a DC005 cable de alimentación - 1 x DC005 power socket - 1 x 18P IC socket - 1 x ULN2803 DIP - 1 x 40P IC socket - 1 x STC12C5A60S2 (programad

Especificación 222,1 kB

Raspberry Pi Starter Learning Kit (Raspberry Pi not included)

https://www.microjpm.com/products/ad59464/
 Motor Driver Module (Based on ULN2003A) - 1x ADC0832 - 1x L9110 motor driver - 1x DC Motor - 1x 4*4 Matrix Keyboard - 1x Breadboard Power Supply Module - 1x 40 pin GPIO Extension Board - 1x 40 pin GPIO Cable - 2x Light 

Especificación 220,4 kB

OBD-II to DB9 Cable [CAB-10087]

https://www.microjpm.com/products/obd-ii-to-db9-cable/
2 7 Chassis Ground 4 2 Signal Ground 5 1 CAN High J-2284 6 3 ISO 9141-2 K Line 7 4 J1850 BUS- 10 6 CAN Low J-2284 14 5 ISO 9141-2 L Line 15 8 Battery Power 16 9 Documents: Pinout Diagram Para más detalles ver el siguiente enlace:  www.sparkfun.com/

Especificación 221,9 kB

REX-C100 Digital PID Temperature Controller

https://www.microjpm.com/products/ad38955/
possible to specify when control output is current output. 5 As control loop break alarm (LBA), only either the ALM1 or ALM2 is selected. Check that power supply voltage is also the same as that specified Etiquetas : POS: URN-7 | POS: STE-4B | REXC1

Especificación 225,4 kB

SCD30 - CO₂ Humidity and Temperature Sensor [SEN-15112]

https://www.microjpm.com/products/a52949/
Sensirion recomienda 7 días de lecturas continuas con al menos 1 hora al día de 'aire fresco' para completar la autocalibración. Características: Power supply voltage: 3.3V - 5.5V NDIR CO2 sensor technology Integrated temperature and humidity sen

Especificación 224 kB

CAN-BUS Shield [DEV-13262]

https://www.microjpm.com/products/can-bus-shield/
N v2.0B up to 1 Mb/s High speed SPI Interface (10 MHz) Standard and extended data and remote frames CAN connection via standard 9-way sub-D connector Power can supply to Arduino by sub-D via resettable fuse and reverse polarity protection. Socket for

Especificación 225,3 kB

LED Cube YELLOW DIY Kit 8x8x8

https://www.microjpm.com/products/ad30342/
O 3mm - 2 x XH2.54 - 40Pin hembra redondo - 9 x 20P IC socket (base integrado) - 9 x 74HC573 DIP - 1 x USB a DC005 cable de alimentación - 1 x DC005 power socket - 1 x 18P IC socket - 1 x ULN2803 DIP - 1 x 40P IC socket - 1 x STC12C5A60S2 (programad

Especificación 222,1 kB

Servo - Generic Continuous Rotation (Micro Size) [ROB-10189]

https://www.microjpm.com/products/servo-generic-continuous-rotation-micro-size/
y continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60°. A standard 3-pin power and control cable is attached and all hardware listed below is included. Features: Voltage: 4.

Especificación 221,4 kB

Raspberry Pi Pico [DEV-17829]

https://www.microjpm.com/products/ad60968/
MHz 264kB of SRAM, and 2MB of on-board Flash memory Castellated module allows soldering direct to carrier boards USB 1.1 Host and Device support Low-power sleep and dormant modes Drag & drop programming using mass storage over USB 26 multi-function

Especificación 225,3 kB

Magnetic Card Reader [SEN-11096]

https://www.microjpm.com/products/ad33421/
ion: This is a simple three track magnetic card reader with serial output. This reader connects to your computer with a DB9 for serial and a PS/2 for power and outputs a 9600bps 8N1 ASCII serial stream. Plug the reader into a serial port (or USB to s

Especificación 219,9 kB


Elementos: 951 - 960 de 1051
<< 94 | 95 | 96 | 97 | 98 >>